The bolt pattern determines whether the disc can be installed on a car.
Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.
Disc bolt pattern is a set of parameters that are arranged into a single geometric model that is either suitable for a particular car or unacceptable for use on it.
Basic parameters of the wheel rim.
- The seat width of the wheel is measured in inches.
- Landing diameter. Also measured in inches.
- The distance from the mounting surface of the disk to the center of the tire. Designated ET.
- The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
- The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.
The PCD parameter depends on the distance between the centers of adjacent holes and on their number.
What kind of chatter does the Daewoo Nexia have?
To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:
- 13/5J PCD 4×100 ET 49 DIA 56.6
- 13/5.5J PCD 4×100 ET 49 DIA 56.6;
- 14/5.5J PCD 4×100 ET 49 DIA 56.6.
Stamped standard 13-inch wheel for Nexia.
Now the markings of a standard Nexia disk become clear:
- 13 and 14 are the diameter of the disc, measured in inches.
- 5.5J (5J) or simply 5.5(5) is the width of the rim in inches.
- PCD 4x100 - four holes, the centers of which are located along a diameter of 100 mm.
- ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
- The landing diameter of the hub hole is 56.6 mm.
A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.
Alternative options
This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.
It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.
Discs
Selecting and purchasing high-quality wheels for the Daewoo Nexia is not difficult. Many brands on the market are suitable for this car model. You can choose products to suit every taste and budget. The most common are stamped wheels, but cast ones can also be purchased if desired. Products of any design, color and shape are presented.
Daewoo Nexia, stamped steel wheels
The size of Daewoo Nexia wheels from the factory can be in three designs, with radii from 13 to 15 inches. But if necessary, it is common among tuning enthusiasts to install even R16 wheels. For this, special spacers are used.
Daewoo Nexia has been produced in various countries since 1994, and since 2016 it has been changed to the Ravon Nexia brand. Regardless of the country of manufacture, the recommended wheel and mount sizes remained the same.
Thanks to factory unification and ease of selection of wheels, you can choose from original, used and cast products. All these options have their advantages and disadvantages. To make the right choice, you need to consider them all.
Original wheels
The car is equipped with such models from the factory. When purchasing original Nexia wheels, you can be sure that the sizes of the mounts will not match, or the wheels will not fit into the arches. Original products are a guarantee that the car will meet all the necessary characteristics of handling, smooth movement, and safety. The car will behave predictably on all types of road surfaces in all weather conditions.
Are VAZ wheels suitable for Nexia?
The bolt pattern determines whether the disc can be installed on a car.
Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.
Disc bolt pattern is a set of parameters that are arranged into a single geometric model that is either suitable for a particular car or unacceptable for use on it.
Basic parameters of the wheel rim.
- The seat width of the wheel is measured in inches.
- Landing diameter. Also measured in inches.
- The distance from the mounting surface of the disk to the center of the tire. Designated ET.
- The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
- The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.
The PCD parameter depends on the distance between the centers of adjacent holes and on their number.
What kind of chatter does the Daewoo Nexia have?
To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:
- 13/5J PCD 4×100 ET 49 DIA 56.6
- 13/5.5J PCD 4×100 ET 49 DIA 56.6;
- 14/5.5J PCD 4×100 ET 49 DIA 56.6.
Stamped standard 13-inch wheel for Nexia.
Now the markings of a standard Nexia disk become clear:
- 13 and 14 are the diameter of the disc, measured in inches.
- 5.5J (5J) or simply 5.5(5) is the width of the rim in inches.
- PCD 4x100 - four holes, the centers of which are located along a diameter of 100 mm.
- ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
- The landing diameter of the hub hole is 56.6 mm.
A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.
Alternative options
This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.
It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.
Proven replacements
Alloy wheel for Daewoo Nexia GM12 (copy of the original disk).
Proven options for replacing factory disks:
- 6Jx14 4x100 ET45;
- 6Jx15 4x100 ET45;
- 5Jx15 4x100 ET45;
- 5Jx16 4x100 ET45;
- 7Jx15 4x100 ET45;
- 7Jx16 4x100 ET45.
Naturally, the landing hub diameter DIA remains stable for everyone - ET 56.6.
Theoretically, it is possible to install disks of a different bolt pattern using adapters, but is it worth doing?
Almost all wheel rims are marked, but there are also those that simply do not have markings. In such cases, we can calculate the bolt pattern ourselves, having only a caliper and a calculator on hand (for those who got a C in math).
There is a simple formula for calculating PCD - B=Nx1.414, where B is PCD, N is the distance between the centers of two adjacent holes. Good luck with your choice, don’t make mistakes with the bolt pattern, and good luck to everyone!
Will VAZ wheels fit?)
Guys, urgently the braid will fit on the steering wheel
by Adminrive Published 10/09/2016
PLEASE TELL ME THE WEBSITE WHERE I CAN ORDER AN ARMREST FOR NEXIUSATION THANK YOU
by Adminrive · Published 08/27/2015
Probably the speedometer sensor and where is it located?
by Adminrive · Published 09.20.2015
- Comments 6
- Pingbacks 0
Look at the post a little lower, there are even photos there
On the vase the bolt pattern is 4x98, on Ksyukha it’s 4x100
I have VAZ winter tires on stamps! The question is, will they fit on the Neusia N150?
Lyokha, tires and wheels no
A hackneyed topic! Take wheels for Nexia and don’t worry about it
Various bolt patterns. You can install it, but 1 bolt out of 4 will be fully tightened
Parameters of alloy wheels
PCD (Pitch Circle Diameter) diameter and the number of these holes.
For example, PCD100/4 - 4 holes with a diameter of 100 mm.
Since the mounting holes are made with a significant tolerance plus in diameter, you can make a mistake in choosing a PCD if it differs from the standard one by a couple of millimeters. For example, a PCD98/4 wheel is often put on a hub with PCD100/4 (98 mm from 100 cannot be distinguished by eye). It is unacceptable. In this case, of all the nuts (or bolts), only one will be fully tightened; the remaining holes will “lead away” and the fasteners will remain untightened or tightened skewed - the fit of the wheel on the hub will be incomplete. While driving, such a wheel will “beat”, in addition, not fully tightened nuts will unscrew by themselves.
Determining PCD by distance between bolt holes
DIA - diameter of the central hole for the hub or the central hole of the disk
ET - offset (or offset) of the disk (measured in mm).
This is the distance between the longitudinal plane of symmetry of the disk and the plane of the hub. The offset can be zero (the plane of symmetry of the disk coincides with the plane of the machine hub), positive (the plane of symmetry of the disk is closer to the center of the machine than the plane of the hub - as in the figure) and negative (further). For each car model, the offset is calculated by the manufacturer to ensure optimal stability and controllability of the car, as well as the least load on the hub bearings. The Germans designate the offset ET (for example, ET30 (mm), if its value is positive, or ET-30, if negative), the French - DEPORT, manufacturers from other countries usually use the English OFFSET. The desire to install wider low-profile tires that have appeared in recent years (sometimes on larger R-size wheels) leads to the need to select a wheel with a reduced ET (i.e. the tire has become wider - you need to move it outward from the body - otherwise it will start to touch it ) . Reducing ET makes the wheel track wider; - this increases the stability of the car and gives it a stylish racing look. An excessive decrease in ET is undesirable, because may result in increased load on the wheel bearings. Increase the reach, i.e. It is usually impossible to narrow the track - the disc will rest against the brake caliper.
How to choose original wheels
First you need to decide on seasonality. For winter, it is recommended to buy wheels one or two inches smaller than for summer.
Maximum safety while driving will be provided only by original rims. A good level of safety is also ensured by products from proven quality brands. It is not advisable to experiment with replicas or used wheels.
For Daewoo Nexia of any year of manufacture there are no problems with the selection of wheel rims of any size. Both cast and stamped products can be installed.
Forgot your password? Enter your email address. You will receive an email with a link to reset your password.
Are VAZ wheels suitable for Nexia?
The bolt pattern determines whether the disc can be installed on a car.
Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.
Disc bolt pattern is a set of parameters that are arranged into a single geometric model that is either suitable for a particular car or unacceptable for use on it.
Basic parameters of the wheel rim.
- The seat width of the wheel is measured in inches.
- Landing diameter. Also measured in inches.
- The distance from the mounting surface of the disk to the center of the tire. Designated ET.
- The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
- The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.
The PCD parameter depends on the distance between the centers of adjacent holes and on their number.
What kind of chatter does the Daewoo Nexia have?
To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:
- 13/5J PCD 4×100 ET 49 DIA 56.6
- 13/5.5J PCD 4×100 ET 49 DIA 56.6;
- 14/5.5J PCD 4×100 ET 49 DIA 56.6.
Stamped standard 13-inch wheel for Nexia.
Now the markings of a standard Nexia disk become clear:
- 13 and 14 are the diameter of the disc, measured in inches.
- 5.5J (5J) or simply 5.5(5) is the width of the rim in inches.
- PCD 4x100 - four holes, the centers of which are located along a diameter of 100 mm.
- ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
- The landing diameter of the hub hole is 56.6 mm.
A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.
Alternative options
This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.
It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.
Proven replacements
Alloy wheel for Daewoo Nexia GM12 (copy of the original disk).
Proven options for replacing factory disks:
- 6Jx14 4x100 ET45;
- 6Jx15 4x100 ET45;
- 5Jx15 4x100 ET45;
- 5Jx16 4x100 ET45;
- 7Jx15 4x100 ET45;
- 7Jx16 4x100 ET45.
Naturally, the landing hub diameter DIA remains stable for everyone - ET 56.6.
Theoretically, it is possible to install disks of a different bolt pattern using adapters, but is it worth doing?
Almost all wheel rims are marked, but there are also those that simply do not have markings. In such cases, we can calculate the bolt pattern ourselves, having only a caliper and a calculator on hand (for those who got a C in math).
There is a simple formula for calculating PCD - B=Nx1.414, where B is PCD, N is the distance between the centers of two adjacent holes. Good luck with your choice, don’t make mistakes with the bolt pattern, and good luck to everyone!
Will VAZ wheels fit?)
Guys, urgently the braid will fit on the steering wheel
by Adminrive Published 10/09/2016
PLEASE TELL ME THE WEBSITE WHERE I CAN ORDER AN ARMREST FOR NEXIUSATION THANK YOU
by Adminrive · Published 08/27/2015
Probably the speedometer sensor and where is it located?
by Adminrive · Published 09.20.2015
- Comments 6
- Pingbacks 0
Look at the post a little lower, there are even photos there
On the vase the bolt pattern is 4x98, on Ksyukha it’s 4x100
I have VAZ winter tires on stamps! The question is, will they fit on the Neusia N150?
Lyokha, tires and wheels no
A hackneyed topic! Take wheels for Nexia and don’t worry about it
Various bolt patterns. You can install it, but 1 bolt out of 4 will be fully tightened
Parameters of alloy wheels
PCD (Pitch Circle Diameter) diameter and the number of these holes.
For example, PCD100/4 - 4 holes with a diameter of 100 mm.
Since the mounting holes are made with a significant tolerance plus in diameter, you can make a mistake in choosing a PCD if it differs from the standard one by a couple of millimeters. For example, a PCD98/4 wheel is often put on a hub with PCD100/4 (98 mm from 100 cannot be distinguished by eye). It is unacceptable. In this case, of all the nuts (or bolts), only one will be fully tightened; the remaining holes will “lead away” and the fasteners will remain untightened or tightened skewed - the fit of the wheel on the hub will be incomplete. While driving, such a wheel will “beat”, in addition, not fully tightened nuts will unscrew by themselves.
Determining PCD by distance between bolt holes
DIA - diameter of the central hole for the hub or the central hole of the disk
ET - offset (or offset) of the disk (measured in mm).
This is the distance between the longitudinal plane of symmetry of the disk and the plane of the hub. The offset can be zero (the plane of symmetry of the disk coincides with the plane of the machine hub), positive (the plane of symmetry of the disk is closer to the center of the machine than the plane of the hub - as in the figure) and negative (further). For each car model, the offset is calculated by the manufacturer to ensure optimal stability and controllability of the car, as well as the least load on the hub bearings. The Germans designate the offset ET (for example, ET30 (mm), if its value is positive, or ET-30, if negative), the French - DEPORT, manufacturers from other countries usually use the English OFFSET. The desire to install wider low-profile tires that have appeared in recent years (sometimes on larger R-size wheels) leads to the need to select a wheel with a reduced ET (i.e. the tire has become wider - you need to move it outward from the body - otherwise it will start to touch it ) . Reducing ET makes the wheel track wider; - this increases the stability of the car and gives it a stylish racing look. An excessive decrease in ET is undesirable, because may result in increased load on the wheel bearings. Increase the reach, i.e. It is usually impossible to narrow the track - the disc will rest against the brake caliper.
The main differences between stamped and cast wheels for Matiz
The difference between stamped and cast car wheels
Stamped designs have gained popularity not only because of their affordable cost, but also for their qualities.
Before releasing their own products for sale, engineers conduct numerous studies.
The laboratory tests the strength of the product, reaction to impacts, endurance, test drive. Taking into account all these details, the manufacturer of Daewoo Matiz guarantees car owners of this brand a high level of safety.
You may be interested in this About original wheels for Toyota
The production process is carried out using modern equipment. Our specialists regularly implement the latest innovative technologies to achieve maximum results. A high-quality anti-corrosion protective coating is applied to the structure. Thus, alloy wheels for the Daewoo Matiz are completely protected from high levels of reagents.
Alloy wheels R13 on Matiz have an original design. The list of products is very diverse; a wide range of models and standard sizes allows the design to be used on cars of almost all brands. Alloy wheels for the Daewoo Matiz reduce fuel consumption.
Important!
Stamped steel products provide reliability, high quality, and strength.
