Replacing the front wheel bearing of Daewoo Nexia

Tools for work

To replace the front wheel bearing on a Daewoo Nexia, you will need the following tools:

1. Jack.
2. Reliable supports - you can use both factory-made and home-made elements. Even strong beams will do.
3. A set of keys.
4. Wheel chocks. In the absence of such, you can use any suitable objects, for example, bricks.
5. Balloon wrench.
6. Circlip pliers.
7. Pullers for ball and steering joints.

Also, when repairing the Nexia, you will need a hammer, drifts, and pliers. You may also need other tools that are not included in this list - it all depends on the specific conditions.

Front wheel bearing Daewoo Nexia: features of choice

Daewoo Nexia front wheel bearing size

The actual size of the front wheel bearing of the Daewoo Nexia depends on the type of wheel. Models before 2008 may have a 13th diameter, in which case the size will be 64*34*37.

For the 14th diameter, the wheel bearing has dimensions of 39*72*37 mm. This information can also be obtained from dealers or managers of a certified service station. The numbers in the catalog cannot change, but new ones may appear, since the assortment is constantly updated.

Daewoo Nexia front wheel bearing number

Catalog numbers of major manufacturers:

Price of front wheel bearing Daewoo Nexia

Products produced by the Volzhsky plant with the VPZ marking will cost from 450 rubles. (cat. no. 537708). Also a good manufacturer is FAG, a world leader in their manufacture (catalog no. 803646). They are about three times more expensive than domestic ones due to the higher quality materials and technologies used.

Dismantling the hub

It should be noted that when replacing the front wheel bearing on a Daewoo Nexia, you have to install a new nut - the old one will become unusable in any case. It is also recommended to simultaneously check the condition of the ball joint and steering tip. If necessary, replacement must be made.

The hub removal procedure is as follows:

1. First, loosen the bolts that secure the wheel. Then you need to flare and loosen the nut.
2. Only after this can the wheel bolts be loosened and the side to be repaired lifted using a jack. Place the removed wheel under the bottom of the car so that if it falls, it will support the car.
3. Unscrew the nut that is located on the steering end. Using a puller you can press it out without any problems. Without a puller, dismantling is problematic, so it is recommended to acquire this tool in advance.
4. Move the tip away from the stand.
5. Remove the two iron caps that protect the caliper bolts from contamination.
6. Unscrew the bolts with a 10mm hex to release the caliper.
7. Remove the caliper and hang it on a wire.
8. Unscrew the nut that secures the ball joint.
9. Using a puller and a hammer, you need to knock out the ball.

Then you need to unscrew the bolt that secures the brake disc and remove it. Then unscrew the nut from the hub. Next you will have to unscrew the nuts that secure the stand to the cup - these elements are located under the hood of the car.

Replacing the Front Wheel Bearing of Daewoo Nexia Video

FCAvto

• Bucks 58.85
• Euro. 62.68

replacing front bearing

Habi deo
Nexia
(DAEWOO NEXIA)

• Location: admin;
• Read: 17232;
• Date: 17-11-2013, 13:15;

To replace the DAEWOO NEXIA front wheel bearing you will need: wrenches “9”, “12”, “19” end heads “30” (for N 100 cars with SONC engine), “32” (for other cars ), wheel bolt wrench, wrench, ball joint puller, also bearing pullers, locking mechanism, rings, hammer.

WARNING: Be careful when purchasing parts: N 100 vehicles with DONC and SONC engines have hubs, wheel bearings and wheel drives of similar design but different sizes. For these reasons, the toolkits are different, but the methods are similar.

TOP TIP: To replace a bearing, it is convenient to use a puller to compress and press commercially available wheel bearings.

NOTE: Front Bearing Replacement Hubby

It is more convenient to do this on a damping support removed from the machine. The manufacturer advises to immediately replace the bearings of both front wheels of DAEWOO NEXIA.

1. Remove the front suspension cushion. (See " replacement

front suspension ").

READ Nissan Almera N16 Oil Change

Video about replacing the front wheel bearing of Daewoo Nexia

5. Screw the stand into the vise and hammer it with a mandrel of suitable diameter (for example, a socket head).

replacement Front wheel bearing Daewoo Nexia

Front Replacement

steering wheel
Bearing Daewoo Nexia
On the
Daewoo Nexia
, it's time to change the hub.

3. Remove the hub. Most likely, the outer half of the bearing inner race remains on the hub.

WARNING: Once the hub has been removed, the bearing cannot be reused and must be replaced.

4. Using a puller, remove it from the hub.

5. Install the bearing inside the cam housing by lightly tapping the mandrel with a hammer to release the bearing snap ring and remove the snap ring with a snap ring puller.

6. Remove the 2nd ring in the same way.

7. Install the removable bearing, pull out the bearing.

Video front bearing 2106 Replacement.

8. Remove the bearing from the knuckle.

9. If a puller is not available, knock out the bearing using a mandrel of the appropriate diameter, since an extruded bearing cannot be reused.

10. Clean the parts and lubricate the inner surface of the bell and the outer surface of the hub with a thin layer of Litol-24 lubricant.

READ Changing the Oil in the Niva 21214 Engine

11. Install the outer snap ring into the knuckle groove.

12. Insert the new bearing completely into the race.

WARNING: When the bearing is pressed against the fuser housing, force must be applied to the outer race of the bearing, otherwise the bearing will be damaged.

13. Install the inner retaining ring.

14. Press the hub against the bearing fully, supporting the inner race with the bearing. bearing .

WARNING: If the bearing inner race is not secured to the support when installing the hub, it will be damaged.

15. Install the shock absorber strut on the car, return to removal.

16. Check and adjust wheel angles if necessary. Use specialized workshop equipment.

Source

Bearing removal

And how can replacing the front wheel bearing on a Daewoo Nexia take place without removing the element itself? To press out the bearing, you will need to pull the ball joint arm down a little to yank the front strut out of place. Be sure to ensure that the drive shaft does not come out. Otherwise there will be more work.

After this, you need to completely unscrew the nuts that secure the stand to the cup. And the stand can be freely removed from its seat.

Please note that it is not necessary to remove the locking ring. But you still have to knock the bearing out of the hub. For this, it is best to use a special puller. The bearing race should come out very tightly. The ring on the hub can be cut off using a grinder.

Replacing the front wheel bearing of Daewoo Nexia

Replacing the front

wheel
bearing Daewoo Nexia
On the
Daewoo Nexia
it's time to change the wheel bearing.

3. Remove the hub. Most likely, the outer half of the inner bearing race remains on the hub.

WARNING: Once the hub has been removed, the bearing cannot be reused and is expected to be replaced.

4. Use a puller to remove it from the hub.

5. Press the bearing inside the knuckle socket with light blows of a hammer through the mandrel to release the bearing retaining ring, and remove the retaining ring using a retaining ring puller.

6. Remove the 2nd ring in the same way.

7. Install the bearing puller and press out the bearing.

Replacing the front wheel bearing of a VAZ 2106 video.

8. Remove the bearing from the knuckle.

9. If there is no puller, knock out the bearing using a mandrel of suitable diameter, because the pressed out bearing cannot be reused.

10. Clean the parts and lubricate the inner surface of the knuckle socket and the outer surface of the hub with a thin layer of Litol-24 lubricant.

11. Install the outer snap ring into the groove of the knuckle socket.

12. Press the new bearing fully into the retaining ring.

WARNING: When pressing a bearing into the knuckle housing, force must be applied to the outer race of the bearing, otherwise the bearing will be damaged.

13. Install the inner retaining ring.

14. Press the hub fully into the bearing, supporting the inner ring of the bearing .

Bearing installation

Installing a new bearing will not be difficult if you warm up the hub a little in advance. Just be careful not to overdo it, or the grease inside the bearing will evaporate.

When installing, you can use a press, vice, puller or hammer. In the latter case, it is imperative to use a spacer made of wood or soft metal (for example, brass or bronze).

Do I need to change the front wheel bearing on the Daewoo Nexia?

If you find play in the wheel bearing of the Daewoo Nexia, you will most likely have to worry about repairing and replacing this part of the front suspension.

Ignoring annoying noise is not an option. If you do not make repairs, the chassis of your Daewoo Nexia may be significantly damaged. And this will lead to troubles along the way. The safety of your car is catastrophically reduced.

Bearings do not fail at the same time. One may be in excellent condition, but the other is out of order. You need to find out which side the breakdown occurred on. I'll tell you how to determine this.

When you turn your car to the left and hear an unwanted sound, you know that the right wheel bearing has become unusable. And, by analogy, evidence of a breakdown of the left element of the front suspension is noise when turning right.

To finally make sure which part you need to change, do the following.

— on the side of the car where you have doubts about the serviceability of the bearing, place a jack;

— grab the wheel with both hands and check for play.

If you still feel any movement, then the front suspension bearing definitely needs repair.

I would also advise you to pay attention to such a thing as the presence of an ABS system. If such a system exists, there is no need to check the wheel geometry. If there is no ABS, repairs become somewhat more difficult. It is imperative to make a diagnosis.

Wheel bearing removal algorithm

It’s worth talking about what manipulations need to be carried out when repairing the Nexia with your own hands. You can remove the bearing using this algorithm:

1. The first step is to dismantle the hub so that the inner ring remains on it.
2. Using a universal three-jaw puller, it is necessary to remove the inner ring of the bearing. It must be changed; the old one cannot be used.
3. Then the retaining ring should be released - to do this, the bearing must be seated inside the cam. The rings are also removed using a puller.
4. Install the puller and remove the bearing. If you do not have a puller, you can use a mandrel or ring of the same diameter. It is not recommended to subject the element to shock loads.

The price of a front wheel bearing for the Daewoo Nexia is not very high - non-original ones can be purchased for 500 rubles (for one wheel). As for the original ones, they will be more expensive - from 1,500 rubles and above.

Replacing a Daewoo Nexia wheel bearing: how to understand that it is required

To find out whether the front wheel bearing of the Daewoo Nexia requires repair and replacement, you need to do the following:

1. Raise the desired side with a jack;
2. Hold the wheel with both hands and check the play.

If there is free play, the problem must be corrected. In the factory, everything is securely fixed with rings on both sides in the grooves of the body and therefore the hub must be stationary.

How to check a wheel bearing:

Front wheel noise:

Another sign of the need for replacement is that the hum disappears/appears when turning. For example, if the noise disappears for a short time when turning right, then the problem is on the left side, and vice versa.

The same signs of malfunction are characteristic of the rear wheel bearings on the Daewoo Nexia.

It is important to know:

The presence of an ABS system is important: it makes checking the chassis geometry unnecessary, and if there is no ABS, then installation is a little more complicated, and diagnostics are a categorical condition. A number of factories producing such spare parts supplement their products with a set of tools (wrenches, nuts and lubricant) to facilitate work on cars with an ABS system. This approach saves the final adjustment of the chassis geometry.

Bearing installation algorithm

All Daewoo Nexia spare parts that are reinstalled must be thoroughly washed and cleaned of dirt.

It is necessary that the inner surface of the knuckle and the outer hub be treated with fresh lubricant. Then perform the following manipulations:

1. Place the outer locking ring into the fist.
2. Press in the new wheel bearing until it rests against the retaining ring. Please note that all the force must be applied to the outer race of the bearing.
3. Install the locking ring from the inside.
4. Now you can install all the elements that were dismantled earlier. Please note that the nut must be tightened with a special torque wrench with a force of 100 Nm.

You will also have to check and adjust the camber and toe of the front wheels, otherwise the tire tread will be destroyed.

Front wheel bearing Daewoo Nexia: numbers and sizes

The actual size of the front wheel bearing of the Daewoo Nexia depends on the type of wheel. Models before 2008 may have a 13th diameter, in which case the size will be 64*34*37.

For the 14th diameter, the wheel bearing has dimensions of 39*72*37 mm.

This information can also be obtained from dealers or managers of a certified service station. The numbers in the catalog cannot change, but new ones may appear, since the assortment is constantly updated.

Daewoo Nexia front wheel bearing number

Catalog numbers of major manufacturers:

Price of front wheel bearing Daewoo Nexia

Products produced by the Volzhsky plant with the VPZ marking will cost from 450 rubles. (cat. no. 537708). Also a good manufacturer is FAG, a world leader in their manufacture (catalog no. 803646). They are about three times more expensive than domestic ones due to the higher quality materials and technologies used.

Replacing the Daewoo Nexia wheel bearing

The hub removal procedure is as follows:

1. First, loosen the bolts that secure the wheel. Then you need to flare and loosen the nut.
2. Only after this can the wheel bolts be loosened and the side to be repaired lifted using a jack. Place the removed wheel under the bottom of the car so that if it falls, it will support the car.
3. Unscrew the nut that is located on the steering end. Using a puller you can press it out without any problems. Without a puller, dismantling is problematic, so it is recommended to acquire this tool in advance.
4. Move the tip away from the stand.
5. Remove the two iron caps that protect the caliper bolts from contamination.
6. Unscrew the bolts with a 10mm hex to release the caliper.
7. Remove the caliper and hang it on a wire.
8. Unscrew the nut that secures the ball joint.
9. Using a puller and a hammer, you need to knock out the ball.

DETAILS: Replacing the cabin filter Mazda 6 GJ. Photos, instructions on how to change the cabin filter of Mazda 6

Then you need to unscrew the bolt that secures the brake disc and remove it. Then unscrew the nut from the hub. Next you will have to unscrew the nuts that secure the stand to the cup - these elements are located under the hood of the car.

Replacing the Daewoo Nexia rear wheel bearing with your own hands: instructions, video, dimensions and numbers

The rear wheel bearing on the Daewoo Nexia is located in the rear wheel hub, which is attached to the brake drum from the inside. The rear hub bearing assembly consists of two open tapered roller bearings, one inner (large) and one outer (small).

With proper operation and maintenance, the spare part will last more than 50,000 km. Reasons for failure that will require replacing the rear wheel bearing of the Daewoo Nexia:

• Leakage of lubricant and ingress of dirt and moisture through the seals (the raceways of the rings, rollers and separator are damaged);
• Driving over potholes and uneven surfaces;
• Wear of the seating surface on the axle shaft and rotation of the axle shaft;
• Drum imbalance, rear hub wear on Daewoo Nexia;
• Other rear suspension problems.

The article describes in detail how to correctly replace the rear wheel bearing on a Daewoo Nexia: make a diagnosis, remove the old one and install a new one. Recommendations on the selection of spare parts are given, as well as the nuances of repairs and instructions for adjusting the bearing clearance. Preview the video on how to replace the rear wheel bearing of Daewoo Nexia.

Replacing Daewoo Nexia rear wheel bearings