How to remove the rear seat backrest of Renault Logan

Renault Logan seats

Every car enthusiast needs to recline the car seats from time to time. Most often this concerns the rear ones, but there are often cases where it is necessary to fold the front elements of the Renault Logan.

The process of folding and repairing seats

If you remove the front elements (including the driver's side) with your own hands, the car enthusiast will not have any particular difficulties. Both on first-generation Renault cars and on second-generation cars, the process of adjusting the backrest with your own hands, the angle of inclination and repair is similar (these manipulations are shown in numerous videos on the Internet).

For the car enthusiast, the Renault Logan car has a seat lift.

Some versions, in addition to the elevator, are equipped with heating, which may fail and to replace it, you will therefore need to remove the front elements (driver's side).

The process of removing, similarly, the driver’s license is described in detail in numerous videos on the Internet.

The frame itself is bolted to the car body. The dismantling process for repair occurs in several stages and is shown in detail in numerous videos:

after unscrewing the bolts securing the base, it is removed and subsequent repair work is carried out;
in case of replacing heating elements, it is necessary to separate the backrest from the seat cushion;
when purchasing a new heater, the owner should carefully check the factory catalog number of the part, since the product may not be suitable for a number of characteristics, this number is important, since if the number does not match, the owner will have to change the element to a part with the appropriate number;
after repairs and separation of the pillow from the backrest, it is necessary to remove the upholstery for subsequent replacement of the heating threads that have failed;
the upholstery is attached with rubber bands to the pillow frame and metal hooks; they also need to be dismantled; when dismantling the upholstery with your own hands, you must be careful not to damage the fabric;
you also need to disconnect the electrical wiring of the heating elements, it is located under the seats in the upholstery;
then replace the failed heating element with a working part;
Assembly of the structure occurs according to the diagram in reverse order.

Dismantling the rear row of elements on cars of different generations has a number of minor differences (you can see what these differences are in the video).

Cars of the first generation did not have the ability to recline the back row; they were bolted to the frame and could only be completely removed.

To do this, you need to perform several operations:

Using a screwdriver, you need to dismantle the clamps of the rear row cushion; to do this, move it forward - there will be locking devices in the lower part;
after removing the fixing devices, the lower part of the element must be dismantled and pulled out of the car;
then use a screwdriver to unscrew the two bolts located on the left and right sides of the rear seat backrest;
then move the seat belts to the side and begin the process of dismantling the backrest, removing it from the latches at the bottom;
after that, pull out the back of the rear seat (due to the massive structure, it is easier to carry out this process with an assistant).

Folding out the seats

The process of folding seats occurs in several stages:

the front seats (driver's) can be folded out using the backrest tilt adjustment knob, with its help you can lower the backrest to the level of the elements of the rear row - the result is a full-fledged sleeping place, which will be appreciated by owners who love to travel;
the rear seats in the second generation of Renault Logan are folded out using release buttons - this does not result in a flat floor, but this design is much more convenient compared to the first generation of the car;
in the first generation, Logan did not have the ability to fold out the rear row; owners had to completely dismantle the back of the rear row.

The process of dismantling and transforming Logan seats with your own hands is extremely simple and will be understandable to any car enthusiast, regardless of the skills and experience of driving a car.

Source: https://PortalMashin.ru/logan/renlog-repair/sidenya-reno-logan.html

The process of folding and repairing seats

If you remove the front parts (including the driver's side) with your own hands , the car owner will not have any special problems. Renault cars and on second-generation cars, the process of adjusting the backrest with your own hands, the angle of inclination and repair is similar (these manipulations are shown in countless videos on the web).

For the car owner, a Renault Logan car has a seat lift.

Some versions, in addition to the elevator, are equipped with heating, which may fail and to replace it, it will be necessary to remove the front parts (driver's side).

The process of removing, similarly, the driver’s license is carefully described in countless videos on the Internet.

The frame itself is bolted to the car body. The dismantling process for repairs takes place in several steps and is carefully shown in numerous videos :

after unscrewing the bolts securing the base, it is removed and subsequent repair work is carried out;
in case of replacing heating elements, it is necessary to separate the backrest from the seat cushion;
when purchasing a new heater, the owner should carefully check the factory catalog number of the part, since the product may not be suitable for a number of characteristics, this number is important, since if the number does not match, the owner will have to change the element to a part with the appropriate number;
after repairs and separation of the pillow from the backrest, it is necessary to remove the upholstery for subsequent replacement of the heating threads that have failed;
the upholstery is attached with rubber bands to the pillow frame and metal hooks; they also need to be dismantled; when dismantling the upholstery with your own hands, you must be careful not to damage the fabric;
you also need to disconnect the electrical wiring of the heating elements, it is located under the seats in the upholstery;
then replace the failed heating element with a working part;
Assembly of the structure occurs according to the diagram in reverse order.

How to Remove the Rear Seat on a Renault Logan ~ AUTOINTERLINE.RU

Renault Logan seats

Every car enthusiast should remove their car seats from time to time. Most often this applies to the rear, but it often happens that the front elements of the Renault Logan also need to be folded.

Remove the rear seat (back) of Renault Logan

For transportation of oversized cargo on Renault Logan

you will need to either buy a roof rack or
remove

Renault Logan 2. Remove the rear seat (part 1)

According to descriptions and videos on the Internet, to remove the Logan seat

, you need to recline the seat and unscrew the back

Dismantling the rear row of elements on cars of different generations has a number of minor differences (the differences of which can be seen in the video).

The first generation cars did not have the ability to tilt the rear rear row , they were bolted to the frame and could be removed entirely.

To do this, perform several operations:

Using a screwdriver, you need to dismantle the clamps of the rear row airbags; to do this, it should be moved forward. fastening devices will be installed in the lower part;
after removing the fastening devices, the lower part of the element must be dismantled and pulled out of the car;
then unscrew the two bolts located on the left and right side of the rear seat back using a screwdriver;
then remove the seat belts and begin the process of dismantling the backrest by pulling it out of the latches at the bottom;
after that, pull out the back part of the backrest (due to the massive structure, it is easier to carry out this process with an assistant).

Deployment of places

The process of folding seats occurs in several stages:

The front seats (driver's) are lined with lumbar backrest adjustment, and you can lower your back to the level of the rear row elements. the result is a complete sleeping floor that will be appreciated by traveler owners;
The rear seats of the second generation Renault Logan are lined with locking buttons. a flat floor was not obtained, but this design is much more convenient than the first generation of the machine;
In the first generation, Logan did not have the ability to fold the rear
row; owners had to completely dismantle the rear part of the rear row.

The process of dismantling and transforming Logan Hands seats is extremely simple and will be understandable to any car enthusiast, regardless of driving skills and experience.

Source: https://autointerline.ru/kak-snjat-zadnee-sidene-na-reno-logan/

How to Remove the Rear Seat Backrest of Renault Logan ~ VESKO-TRANS.RU

Renault Logan seats

Every car owner sometimes needs to recline the car seats. In most cases, this applies to the rear ones, but there are often cases where it is necessary to fold the front elements of Renault Logan.

Remove the rear seat (back) of Renault Logan

For transportation of oversized cargo on Renault Logan

you will need to either buy a roof rack or
remove

Renault Logan 2. Remove the rear seat (part 1)

According to descriptions and videos on the Internet, to remove the Logan seat

, you need to recline the seat and unscrew
the back.
Dismantling the rear row of elements on cars of different generations has a number of minor differences (what differences you can see in the video).

Cars of the first generation did not have the ability to recline the back row; they were bolted to the frame and could only be completely removed.

To do this, you need to perform several operations:

using a screwdriver, you need to dismantle the clamps of the rear row ; to do this, move it forward - there will be locking devices in the lower part;
after removing the fixing devices, the lower part of the element must be dismantled and pulled out of the car;
then use a screwdriver to unscrew the two bolts located on the left and right sides of the rear seat backrest;
then move the seat belts to the side and begin the process of dismantling the backrest, removing it from the latches at the bottom;
after that, pull out the back of the rear seat (due to the massive structure, it is easier to carry out this process with an assistant).

THIS IS INTERESTING: Renault Logan body galvanized or not

How to remove the back seat on a Renault Logan

Any car owner sooner or later is faced with the need to unfold or fold the seats in his car, including, of course, the French model Renault Logan. Often the rear seat is affected, but sometimes the front seats also need to be folded down.

How to properly fold and repair seats

If you need to remove the front seats in a car yourself, then the car owner does not have any difficulties. For example, in Renault Logan models of the first and second generation, direct adjustment of the backrest yourself, as well as adjustment of the backrest angle according to the type of tilt and minor repair work are similar; now on the Internet there are many video instructions on how to do this.

I would like to note that in Renault Logan there is a special elevator near the seat.

And now, in addition to a special elevator, some models are equipped with heating, which may also fail at some point due to improper operation, then a replacement will need to be made, and the driver or front passenger seat will need to be removed. Many people are interested in how to remove the seat correctly. This is what we will talk about in this article.

So, the seat frame is held on by bolts that are attached to the car body. The process of removing the seat for repairs is carried out in several stages, below we provide detailed instructions on how to remove the seat in a representative of the French automobile industry Renault Logan:

First you need to unscrew the bolts that secure the chair to the base.
If you need to replace the heating system, then the seat backrest needs to be separated from the cushion.
If heating elements are replaced with new ones, then when purchasing them, be sure to check them with the catalog serial number of the original part, otherwise they may not fit.
After the repair has been carried out, you need to remove the upholstery from the chair to replace the heating threads, which, in fact, failed.
Soft upholstery is almost always secured with rubber bands to a special pillow frame, as well as with special metal hooks, which will also need to be removed. When removing the upholstery yourself, you need to be extremely careful so as not to damage the upholstery fabric.
Carefully disconnect the electrical wiring located in the upholstery directly under the seats from the existing heating elements.
After this, you can safely replace the broken heating element with a new part.
You need to assemble the chair in the reverse order, so to speak, as indicated in the instructions.

Now that you understand how to remove the front or other seat in a Renault Logan car, you need to figure out how to remove the rear seat.

The 1st generation model never had the necessary ability to recline the back of the rear row of seats, since they were tightly screwed to the frame itself, and they could only be completely removed.

Fuel consumption Renault Duster

Renault Duster on gas

Renault Duster trunk volume

So, to remove the entire rear seat, use the following instructions:

Armed with a screwdriver, you should remove the clamps of the cushion of the immediate rear row of seats; to do this, you need to move it forward a little and you will see that the clamp is located in the lowest area of the entire chair.
Immediately after the locking device is removed, remove the lower part of the seat and pull it out of the car.
Again, using a screwdriver, you need to unscrew a couple of bolts that are located on the right and, accordingly, the left side of the back of the rear seat directly.
Then we move the seat belts to the side and remove the seat back; it must be removed from the locking device at the very bottom.
Due to the fact that the backrest design is very massive, it is advisable to resort to outside help.

How do car seats fold out?

To fold the seats in a car from France Renault Logan, you need to do a few simple manipulations:

All front seats, including the driver's seat, can be reclined using the seatback tilt adjuster; you need to lower the backrest even to the level of the rear row seats, and then you get a spacious sleeping area that will appeal to those who like to travel.
In the 2nd version of the Logan model, all rear seats can be easily and simply folded out using locking buttons, and you will not achieve a flat floor, but this design is much better compared to the 1st generation Logan.
The 1st generation model initially did not have the ability to fold out the rear row of seats, and the only way owners had to increase space was to completely remove the backrests of the rear seats from the car.

In conclusion, I would like to note that the process of removing and, of course, unfolding car seats in a Renault Logan car with your own hands is easy and simple, and intuitively understandable to all car owners, regardless of what skills they have or how long their driving experience is. However, many are interested in how to replace the original seats; experts say that it is possible to replace them with any chair, the most important thing is that it is suitable in size and fastenings.

Source: https://ZamenaRenault.ru/logan/obshhee-temy/snyat-zadnee-sidene.html

How to Remove the Rear Seat on Logan 2

as a take off

back seat on Renault Logan

Any car owner at some point is faced with the need to disassemble, as it is also called folding, the seats in their car, including, of course, the French model Renault Logan . Often exposed to the back seat

, but sometimes the front ones have to be folded back.

How to properly fold and repair a seat

If you need to remove the front seats of a car yourself, then working with the car owner will not be difficult. For example, the first and second generation Renault Logan models, which directly adjust the backrest on their own, and also adjust the backrest angle according to the type of inclination and minor similar repairs, there are now many video instructions on how to do this on the Internet.

It should be noted that Renault Logan has a special lift in the seat.

And now, in addition to a special elevator, some models are equipped with heating, which can also very badly fail at some point during improper operation, then it will need to be replaced and it will need to take off

driver's or front passenger's seat. Many people are interested in how to properly remove the seat. We'll talk about this in this article.

First, unscrew the bolts securing the chair to the base.
If you need to replace the heating system, separate the backrest from the cushion next to the seat.
If heating elements are replaced with new ones, the original serial number of the original part must be agreed upon at time of purchase, otherwise they may not be applicable.
After the repair, it is necessary to remove the gasket from the chair in order to replace the heating threads, which, in fact, are out of order.
The upholstery is almost always secured with elastic bands for a special pillow frame, as well as special metal hooks, which will also need to be removed. When removing upholstery, you must be extremely careful not to damage the upholstery fabric.
Carefully disconnect the wiring harness located just under the seats from the existing heating elements.
You can then safely replace the broken heating element with a new part.
It is necessary to assemble the chair in the reverse order as indicated in the instructions.

READ How to Remove Exhaust Manifold Ford Focus 2

Renault Logan 2. Remove the rear seat (part 1)

How to remove the rear seat of Renault Logan Video |

According to descriptions and videos on the Internet, delete the place for logan

, you need to fold the seat and unscrew the backrest.

Now you have figured out how to remove the front or other seat in a Renault car. logan

, you need to figure out how to shoot
the backseat .
The 1st generation model never had the much-needed ability to fold the rear row of seats, as they were firmly attached to the frame and could be removed entirely.

So take off

whole back
seat
. Follow these instructions:

Armed with a screwdriver, you need to remove the cushions of the straight rear row of seats; to do this, slightly push it forward, and you will see that the lock is located at the bottom of the entire chair.
Immediately after removing the locking device, remove the lower part of the seat and remove it from the passenger compartment.
Again, using a screwdriver, unscrew the pair of bolts that are located to the right and respectively to the left of the back of the rear seat directly.
Then remove the seat belts and remove the backrest, it must be removed from the locking device at the bottom.
Since the backrest structure is very massive, it is advisable to seek help.

READ Tighten Timing Chain Chevrolet Cobalt

How does automatic assembly work?

To fold the seats in a car from the French Renault Logan, you need to take a few simple steps:

How to remove the rear seat of Renault Logan 2 |

All the front seats, including seat , are reclined using the backrest tilt adjuster; you need to lower the backrest even to the level of the rear row seats, and then you will get a spacious place that will delight travel lovers.
In the Logan 2 version, all rear seats fold easily and simply using locking buttons without reaching the flat floor, but this design is much better than the first generation Logan.
The first-generation model initially did not have the ability to accommodate rear
seating, and the owners had the only way to increase space. completely remove the backrests from the car.

How to remove and install the rear seat on a Renault Logan

This can be done by pressing a special button.

How to remove a seat on a Renault Sandero

Unscrew the two bolts and lift the backrest, removing its clamps from the holes in the rear partition of the body.

Folding rear seat. Folding out the rear seat cushion. Review of the new Renault Logan 2 Renault Logan Universal

Locate the screws that secure the trim to the radiator frame. But before traveling to Karelia, I decided to check how feasible this was.

From such movements they will easily return to working condition and let go of the pillow. Locate the airbag clips located at the base of the body and carefully remove them from the holes. The machine is equipped with a manual control mode, but it is almost never used.

He threw the seat along the left side, also turning it over. The headrests of the front seats successfully fit sideways between the backs of the front seats. I left the rear headrests and the brace with bolts in the garage for the duration of the trip.

In principle, the result was an almost flat surface, suitable for sleeping even without an air mattress. There is a small step in the front seats.

But the expediency of these movements is very doubtful, because: But it’s faster to put up a tent, and it’s more comfortable and spacious to sleep there; - requires freeing up space in the trunk for your feet and especially in the rear cabin - where do you put things? On our trip, the entire seat in the back was covered with an even layer of all kinds of clothing and food, and there were five liters of water at our feet; — initially it was supposed to spend the night like this in the rain, but manipulations with the pillows are only possible with the rear doors slightly open, while you yourself are outside.

And the second person either won’t be able to stay inside, or will have to remember the game Aladdin on the console - let the tiltable pillows pass over them.

But another option is closer to reality: I don’t care that it’s inconvenient. That’s why I swapped the backrest with the seat, because in the standard version the front seats rest against the sofa and don’t fully recline.

You can mess something up with the frame of the guide seats, re-drill a couple of centimeters forward. A similar element of the rear seat is best removed with an assistant.

THIS IS INTERESTING: Replacing ball joints for Renault Logan

The next element to remove will be the backrest. Unscrew the two mounting bolts and remove the clips from the holes on the rear bulkhead. Move the seat belts and remove the backrest from the passenger compartment.

You only need to unscrew two bolts on the left and right sides. If the seat belts are faulty and prevent you from doing what you intended, simply remove them from their mountings. To do this, remove the cover from its buckle and unscrew the bolt securing it.

And then, using a flat-head screwdriver, remove the screw securing the trim located in the center of the body. You will spend no more than minutes of your personal time dismantling one seat.

To remove the seats of the first row, you need to open the cover; the easiest way to do this is to use a flat-head screwdriver, prying the cover from above. Under the cover you will see a bolt that needs to be unscrewed and removed.

Folding rear seat backrest Renault Logan 1st generation

First, you need to unscrew the screws that hold the decorative plastic trims in place and remove the decor. After this, the back part of the lining must be bent back, slightly moved to the left, and then moved forward and removed in one motion.

Perform all movements carefully and carefully so as not to damage the plastic parts of the seats. By performing this simple operation several times in a row, you will be able to perform it automatically in the future.

When removing decorative parts, help yourself with a flat-head screwdriver, but never use excessive force.

Source: https://diabloarea.ru/reno-logan/%D1%80%D0%B5%D0%BD%D0%BE-%D0%BB%D0%BE%D0%B3%D0%B0%D0% BD-%D0%BA%D0%B0%D0%BA-%D1%80%D0%B0%D0%B7%D0%BB%D0%BE%D0%B6%D0%B8%D1%82%D1% 8C-%D0%B7%D0%B0%D0%B4%D0%BD%D0%B5%D0%B5-%D1%81%D0%B8%D0%B4.html

Rear seat removal process

Removing the rear seat on a Renault Logan is quite simple; you just need to have a wrench, a screwdriver and a pair of hands of a reliable friend nearby, since the back of the seat is quite heavy.

First of all, we take out from the car everything that will only interfere with further work, such elements include rubber mats and a rear parcel shelf.

Read more: Hyundai Grand Starex video review

WD-40

We pull the pillow by its base.

A similar element of the rear seat is best removed with an assistant.

You only need to unscrew two bolts on the left and right sides.

If the seat belts are faulty and prevent you from doing what you intended, simply remove them from their mountings. To do this, remove the cover from its buckle and unscrew the bolt securing it. And then, using a flat-head screwdriver, remove the screw securing the trim located in the center of the body.

We take out the belt bracket; to do this, you need to pull off the lining. You will feel some serious resistance from the fasteners while doing this type of work, but don't worry, they are designed to remain intact even in an accident. So, breaking them will be quite problematic.
After the bracket itself, we remove the “tongue” of the seat belt itself.
We remove the bottom bracket, the trim and take out the inertial coil assembly.

After this, when the rear backrest is completely free and nothing interferes with it, with the help of an assistant we pull it out of the cabin.

Note!

Before loading additional weight into your vehicle, consult your Logan's owner's manual for help. Since for cars with different engine sizes, the load capacity will be different.

Also, pay special attention to maintaining the integrity of all small parts and fasteners. If at least one of them breaks during assembly, you will get one uncomfortable rear sofa that will only “walk” easily when traveling on it.

How to remove the back seat from a Renault Logan - article on the portal avtoremont13.ru

It is best to dismantle the rear seats of a Renault Logan car with an assistant.

Good day! I bought covers and ran into the problem of removing the rear seat sofa. In the Internet

Cars of the first generation did not have the ability to recline the back row; they were bolted to the frame and could only be completely removed. Carefully move the seat back as far as possible. We take out the belt bracket; to do this, you need to pull off the lining.

Before you begin, thoroughly wash and then wipe the bumper and mudguards with a dry, clean cloth to reduce the amount of dirt that may get on you in the future.

Once everything is done, try to lightly rock the seat from side to side. From such movements they will easily return to working condition and let go of the pillow. We pull the pillow by its base. We unscrew the two fastening bolts located on the sides and take it out of the cabin.

A similar element of the rear seat is best removed with an assistant. The next element to remove will be the backrest. It is most convenient to do this operation together.

How to remove the back seat from a Renault Logan

If you have to transport large items quite often, then it makes sense not to reinstall the rear seat back bolts.

This will significantly speed up the removal of the backrest - to do this, it will be enough to lift it, remove it from the fastenings and pull it out of the cabin.

It is convenient to transport the removed backrest of the Renault Logan rear seat by placing it between the backrests of the front seats and the raised seat of the rear sofa or in its place. In addition, there is another way to quickly increase the trunk space of Renault Logan by installing the rear seat back on small door hinges, as shown in this video. Release the rear parcel shelf and remove the floor mats.

Gently pull the rear seat cushion forward. Locate and remove the seat clips from the holes in the body. It is possible that the fasteners will stick to the holes due to long use.

In this case, without using special physical force, swing the clamps in several approaches, pulling the pillow in different directions. Locate the two bolts that are located at the bottom, right and left of the rear seat back. Unscrew the two bolts and lift the backrest, removing its clamps from the holes in the rear partition of the body. Move the seat belts to the side and pull the backrest out of the passenger compartment.

If the belts are in poor condition, remove them from the fastenings. To do this, remove the belt buckle cover and unscrew the bolt securing it. Then use a screwdriver to unscrew the screw of the upper fastening of the trim on the central pillar of the body. To do this, pull back the facing material.

Do not pay attention to the resistance of the fasteners; the fastenings are made with emergency situations in mind, so it is quite difficult to break them. After the bracket, it is also necessary to remove the tongue of the seat belt. Pull the entire inertia coil out of the body pillar.

Pull the released rear backrest out of the passenger compartment. It is best to dismantle the rear seats of a Renault Logan car with an assistant.

Please note: Take a look at the instructions to find out how much cargo can be safely transported in the cabin of a Renault Logan car. Check that the cargo is securely secured in the cabin. Helpful advice Be responsible in maintaining the integrity of all small parts, especially fasteners.

If you damage at least one of them, you will get an absolutely uncomfortable rear sofa during assembly, the cushion of which will move during movement. Sometimes seat dismantling is performed for other reasons.

Features of a Renault Logan car with automatic transmission

Move the seat belts and remove the backrest from the passenger compartment. You only need to unscrew two bolts on the left and right sides. If the seat belts are faulty and prevent you from doing what you intended, simply remove them from their mountings.

To do this, remove the cover from its buckle and unscrew the bolt securing it. And then, using a flat-head screwdriver, remove the screw securing the trim located in the center of the body. We take out the belt bracket; to do this, you need to pull off the lining.

Source: https://avtoremont13.ru/renault/%D1%81%D0%B8%D0%B4%D0%B5%D0%BD%D1%8C%D1%8F-%D1%80%D0%B5% D0%BD%D0%BE-%D0%BB%D0%BE%D0%B3%D0%B0%D0%BD.html

How to remove the rear seats on a Renault Logan?

Good day! I bought covers and ran into the problem of removing the rear seat sofa. No matter how much I searched on the Internet, they always write that you just need to lift it and pull it out of the clamps. I pull on the sofa and it’s as if something is holding it in two places on the right and left near the back. Maybe there are some kind of fastenings there, like bolts? Tell me how to remove the sofa? In advance, very grateful!

IN 1

Removing the rear seat on a Renault Logan is quite simple; you just need to have a wrench, a screwdriver and a pair of hands of a reliable friend nearby, since the back of the seat is quite heavy.

STEP 1: First of all, we take out of the car everything that will only interfere with further work, such elements include rubber mats and a rear parcel shelf.

STEP 2: Next, we remove the clamps that hold the seat cushion in place, but if they do not give in the first time, you should lightly treat the areas with WD-40 (the connections should be handled carefully, without staining the seat upholstery). Once everything is done, try to lightly rock the seat from side to side. From such movements they will easily return to working condition and let go of the pillow.

STEP 3: Pull the pillow by its base. We unscrew the two fastening bolts located on the sides and take it out of the cabin. A similar element of the rear seat is best removed with an assistant.

STEP 4: The next piece to remove is the backrest. Unscrew the two mounting bolts and remove the clips from the holes on the rear bulkhead. Move the seat belts and remove the backrest from the passenger compartment

STEP 5: You only need to remove two bolts on the left and right sides.

STEP 6: Pull out the belt bracket; to do this, you need to pull off the lining. You will feel some serious resistance from the fasteners while doing this type of work, but don't worry, they are designed to remain intact even in an accident. So, breaking them will be quite problematic.

STEP 7: After the bracket itself, we remove the “tongue” of the seat belt itself. We remove the lower bracket, the trim and pull out the inertial reel assembly.

STEP 8: After this, when the rear backrest is completely free and nothing interferes with it, with the help of an assistant we pull it out of the cabin.

How to remove the rear seat of Renault Logan

We remove the rear seat on a Renault Logan ourselves

A very popular model of the French automotive industry, Renault Logan, rightfully occupies a leading position in the Russian market. Despite its budget, the car is very reliable and practical to use. This versatility of the Logan provides decent ground clearance and ample trunk capacity. But how do you want to move large cargo? After all, the rear seats on this car don't fold down!

The video has a moment on how to remove the back seat and raise the backrest!

Rear seat removal process

It's easy to remove the rear seat on a Renault Logan, just have a wrench, a screwdriver and a pair of hands from a trusted companion, as the backrest is quite heavy.

The first thing we do is get everything out of the car that will interfere with further work, such items include rubber floor mats and a rear parcel shelf.

WD-40

Renault Logan 2. Remove the rear seat (part 1)

According to descriptions and videos

on the Internet, to remove
the Logan seat
, you need to recline the seat and unscrew the backrest.

The note!

Please read your Logan's owner's manual before loading additional weight into your vehicle. For vehicles with different engine sizes, the load capacity will be different.

Also pay special attention to maintaining the integrity of all small parts and fasteners. If even one of them collapses during assembly, you'll end up with one uncomfortable backseat that will easily "walk" as you cruise around it.

THIS IS INTERESTING: Replacing the front bearing of Renault Logan

Tips from loggers

Some Logans owners who have been using the above method for a long time are used to transporting bulky goods, they share their advice:

If you want to transport loads, just don't overtighten the bolts. Back fastening. Without them, the removal process is reduced several times, and without them the back will not go anywhere. However, the bolts should be kept in a safe place just in case.

Source: https://avto-melvin.ru/kak-snjat-zadnee-sidenie-reno-logan-video/

How to remove the rear seat backrest of Renault Logan

Renault Logan seats

The process of folding and repairing seats

Folding out the seats

The process of folding and repairing seats

How to Remove the Rear Seat on a Renault Logan ~ AUTOINTERLINE.RU

Remove the rear seat (back) of Renault Logan

Renault Logan 2. Remove the rear seat (part 1)

Deployment of places

How to Remove the Rear Seat Backrest of Renault Logan ~ VESKO-TRANS.RU

Remove the rear seat (back) of Renault Logan

Renault Logan 2. Remove the rear seat (part 1)

How to remove the back seat on a Renault Logan

How to properly fold and repair seats

How do car seats fold out?

How to Remove the Rear Seat on Logan 2

How to properly fold and repair a seat

Renault Logan 2. Remove the rear seat (part 1)

How to remove the rear seat of Renault Logan Video |

How does automatic assembly work?

How to remove the rear seat of Renault Logan 2 |

How to remove and install the rear seat on a Renault Logan

How to remove a seat on a Renault Sandero

Folding rear seat backrest Renault Logan 1st generation

Rear seat removal process

Note!

How to remove the back seat from a Renault Logan - article on the portal avtoremont13.ru

How to remove the back seat from a Renault Logan

Features of a Renault Logan car with automatic transmission

How to remove the rear seats on a Renault Logan?

How to remove the rear seat of Renault Logan

Rear seat removal process

Renault Logan 2. Remove the rear seat (part 1)

The note!

Tips from loggers

see also

Comments 21