How to set the clock on the Sherkhan Magikar 5 alarm and the hands-free function

Author: Victor

The Sherkhan 5 alarm with auto start is a budget system and is intended for use in cars whose electrical voltage is 12 volts. The car alarm has two-way communication, which operates within a radius of 1500 m.

[Hide]

Characteristics of the Scher-Khan Magicar 5 alarm

This signaling model can be installed on a car with either a manual transmission or an automatic transmission. The security device is powered by a battery.

Main functions

Options that the multifunctional key fob communicator performs:

• confirmation of completed commands through sound or vibration;
• protection of the communication channel from interception of code data, the system is called “Magic Code”;
• playback of sound signals when the alarm mode is activated;
• backlight of the device’s liquid crystal screen;
• designation of the charge of the power supply inside the communicator;
• determining the voltage level in the vehicle's electrical network;
• designation of the temperature in the car interior;
• determining the current time on the screen;
• displaying the operating time of the power unit started automatically;
• the ability to remotely start the car engine;
• setting the start time of the power unit accurate to minutes;
• reminder mode via sound or visual messages;
• possibility of programming all anti-theft installation options.

Description of options performed by the microprocessor module:

• remote start of the power unit on vehicles with any type of transmission;
• operation of the system on gasoline and diesel internal combustion engines, including those equipped with turbines;
• the ability to start the power plant upon a command sent from the communicator;
• option to configure remote start by timer, every 2 hours, or by alarm every day;
• the ability to monitor the state of a running engine in accordance with signals sent from the generator set or based on noise in the electrical network;
• availability of a personal password to access the vehicle interior in case of loss of the key;
• use of power outputs to control the central locking, tailgate, and light alarm;
• setting the type of blocking relay - normally closed or normally open;
• automatic activation mode of the protective option;
• sound warning before activating automatic security mode;
• reactivation of the protection function if the vehicle door was not opened;
• the ability to activate the protection mode without being accompanied by siren signals;
• the presence of two universal programmable channels used to control additional equipment;
• microprocessor module allows for additional connection of positive and negative door controllers;
• the presence of a separate input for installing a negative luggage compartment sensor;
• the ability to close and open door locks when starting and stopping the power unit in automatic mode;
• activation of the protection mode with or without confirmation signals;
• option to warn the car owner about an open door with a light alarm; this mode must first be programmed;
• Panic function, which allows you to activate the siren and light alarm on command;
• Hands-free option, which makes it possible to automatically turn on or turn off the protective function if the car owner approaches or moves away from the car;
• function of warning the driver about the side headlights being turned on.

The Autoazart channel briefly talked about the options and capabilities of the Sherkhan Magikar 5 security complex.

Technical specifications

Main properties of the anti-theft installation:

• the range of the communicator is up to 1500 meters in ideal terrain;
• The key fob is powered by AAA batteries;
• optimal operation of the anti-theft system is possible in an on-board network of 9-18 volts;
• The current value when the system is running is 20-35 mA;
• the temperature range at which the security complex operates is from -40 to +85 degrees Celsius;
• The total weight of the microprocessor module is 270 g.

Car owner alert signals are divided into several groups:

• sound for the siren - when the alarm mode is activated, their duration is 30 seconds, the signals are played continuously;
• optical for car headlights - signals with a power of 1 Hz and a duration of 30 seconds operate on two channels and are reproduced intermittently;
• using a radio channel - information is transmitted to the communicator and reproduced intermittently.

The exact range of the key fob depends on many factors:

• power supply charge;
• presence of interference in the area;
• obstacles in the form of large structures, structures, transformer substations;
• weather conditions.

Information is transferred to the communicator via a secure channel using encoding.

All electrical circuits of the security complex are protected by safety devices, resistor devices and transistors. To prevent voltage surges and interference, the system is equipped with varistors. If errors related to polarity are made during connection, this will not affect the operation of the signaling, since the power supplies are equipped with diode elements.

Contact controllers respond to opening door locks or turning the key in the ignition switch. If such a sensor is triggered, the alarm will play an alarm signal without the ability to turn off without the remote control. The security system with automatic start Sherkhan 5 also reacts to physical impacts on the body and, when detected, issues alarm signals.

The current values ​​for protecting electrical circuits are given in the table.

User guide

To control the anti-theft complex, a key fob or ignition key can be used. If configured correctly, this procedure is carried out using a panic button. Using the remote control, you can program functions and set a password for emergency shutdown or activation of the system.

Setting up a PIN code

To set up a personal password, you need to enter programming mode:

1. The vehicle is disarmed.
2. The car door lock opens.
3. The ignition is activated by installing and turning the key in the lock. The engine should not start.
4. The third and fourth keys are pressed on the communicator key fob. The alarm will blink once and the siren will sound. If the signal is triple, this indicates an unsuccessful attempt to enter the password setting mode.
5. The first digit of the code is entered, for this the consumer is given four seconds after the siren signal. To set values, use the communicator keys; the selected number corresponds to a button. If the symbol is received successfully, the alarm will play the appropriate number of flashes and siren sounds.
6. Subsequent numbers are indicated identically; the car owner is given four seconds to enter each. When the last character is entered, the system will automatically exit the setup mode. The car owner will be informed about this by a double siren signal and two flashes of light devices.
7. You can then turn off the ignition and lock all the car doors.

To unlock a vehicle using a code, follow these steps:

1. The car alarm goes off.
2. The driver's door opens.
3. The key is inserted into the lock and the ignition is activated.
4. The car owner taps the call controller ten times. The time interval between impacts should be 1.5 seconds. With each subsequent strike, the diode element will blink red.
5. Each password character is configured using the stroke method, their number must correspond to the number. Input confirmation is carried out every 1.5 seconds. As each digit is indicated, the diode will blink blue.
6. Similarly, each character of the password is indicated. In confirmation, the alarm will blink with lights and sound a siren.

If the car owner enters the PIN code settings mode, the LED light will begin to flash blue.

The channel “Videomax12345” spoke about the main settings and functions of the anti-theft system.

How to enable security mode?

You need to start the live mode after turning off the ignition and closing all the door locks of the car. To complete the task, click the first key on the remote control. This will block the door locks and starter mechanism.

When this function is activated, the following occurs:

• the siren sounds once;
• car lights blink;
• the diode indicator flashes on the block at intervals of 1 second;
• on the communicator display, the vehicle headlights blink five times and the lock indicator appears;
• The remote control emits a melodic signal.

An indicator in the form of a locked pad is displayed on the communicator display until the security mode is disabled. When armed, the alarm constantly monitors and analyzes the readings issued by the controllers. 30 seconds after the protection is turned on, the sensitivity sensor is activated. If the power unit remains running, the procedure for turning on the security mode is performed in the same way. All doors are locked and the first key on the pager is clicked.

But the sensitivity controller will remain off until the ignition is on. The security mode indication will be similar. 30 seconds after the power unit is turned off, the signals will be checked.

User Sergey Gorin showed several ways to control the security mode of the Magikar 5 alarm.

System check

To diagnose the state of the anti-theft installation, the fourth key is used. After pressing it, the car alarm analysis data will be displayed on the communicator screen. Information about the inspection will be confirmed by siren signals, as well as light alarms.

Disabling the system

To disarm the security, use the second key of the communicator. In confirmation, the siren will play one signal and the vehicle's lights will turn on. The car's headlights will blink on the pager screen and an indicator with an open lock will appear.

Equipment

Place the siren with its horn down or to the side. The value of each code digit can vary from 1 to 9. If you need to change more than one function from the Menu you have selected, then selecting each function to change must begin with STEP 1.

The system can be equipped with any siren in accordance with the wishes of the owner, including those where there is no possibility of adjustment. An alarm about turning on the ignition will be indicated by flashing side lights on the key fob communicator, sound and vibration signals. The number of signals will correspond to the number of the selected function.

Adjusting the volume of siren confirmation signals You can adjust the volume of the siren's short beeps. Using a programmable function, you can limit automatic starts to 5th, 7th, 10th, or even abandon the limitation altogether. To adjust the sensitivity, the sensor has a step regulator with three positions. Entering programming mode and selecting the programming menu. There is plus 12 V on this wire when the ignition is on and in starter mode.

PURPOSE

Stage 3. By pressing the buttons mounted on the communicator, the driver selects the required parameter value, confirmed by siren signals and flashing hazard lights. Use a starter interlock circuit. When silent mode is turned on, the communicator's buzzer remains active. The code is entered and recorded using the car's ignition switch.

The time between impacts should be less than 1.5 seconds. If you heard three siren signals and three flashes of the alarm system, then the system has not entered programming mode.

Note: If, when choosing a function, you made a mistake with the number of clicks and or there are no siren and alarm signals, then you must repeat all the steps starting from STEP 1. To adjust the sensitivity, the sensor is provided with a step regulator with three positions. I bought a signaling system with az. Management and configuration of Scher-khan magicar

Keychain - communicator

Before using the remote control, you must install a power source into it.

To do this, remove the protective cover from the back of the communicator into which the battery is inserted, observing the correct polarity. After this, the lid closes.

Indicator designation

Labels of buttons on the remote control display

Description of symbols on the communicator screen:

• A - operation of the power unit by timer;
• B — turbo timer option;
• C — passive security activation mode;
• D — option to automatically activate security without clicking on the keys;
• E - activated siren;
• F—sensitivity controller disabled;
• G—the communicator has the vibration alert function enabled;
• N - control of door locks after activation of the ignition system;
• J - open luggage compartment door;
• K - the power unit is started in automatic start mode;
• L — state of the anti-theft installation;
• M - open door locks;
• N - information field for displaying clock data, as well as temperature conditions during automatic start;
• О — Valet service mode is enabled;
• P - the car has a light alarm or the side lights are not turned on;
• Q - activation of the sensitivity controller;
• R—communicator power supply icon;
• S—signal level.

Main functions of the key fob

To adjust basic parameters and set functions, use the button combinations shown in the table.

How to get the key fob into working condition?

The procedure for binding a new communicator is as follows:

1. The key is inserted into the lock, after which the ignition is turned on and off three times. The light alarm should sound once, indicating that you have entered the setup mode.
2. Over the next four seconds, you must click on the first button on the communicator.
3. Then the pager code is entered into the memory of the microprocessor module.

The car owner can register no more than three communicators. Therefore, when setting up the fourth device, information about the first is deleted from the microprocessor memory. To exit the settings mode, you must not touch the key fob for four seconds.

The MasikBonLive channel talked about independently linking a new communicator to a microprocessor alarm module.

Setting up autorun

You can set the autostart option on the Sherhan system in four options:

• by command:
• by time;
• by air temperature;
• to reduce the voltage in the vehicle's on-board network.

Configuring launch by command

Activation of the option is done as follows:

1. The transmission lever is set to the neutral position, and the handbrake is activated. If the car is equipped with an automatic transmission, the gearshift knob is moved to the parking position.
2. All vehicle door locks are locked.
3. Button 2 on the communicator is pressed for two seconds.
4. The ignition is turned off, the driver leaves the car.
5. When the driver's door closes, this should stop the engine.
6. To subsequently start the power unit, click the second key on the communicator.

Setting a timed trigger

The consumer can configure the option to operate daily, repeating every 24 hours. You can also configure it to run every 2, 4 or 8 hours. To activate the function, you must complete the reservation procedure.

To complete the task you need:

1. Disable the timer function. To do this, click keys 2 and 4.
2. To activate the programming mode, press buttons 1 and 2 and hold them down for 2 seconds.
3. To enter the setup menu, click the fourth key 13 times. A beep will sound with each subsequent click.
4. The repeat time is selected by pressing the keys. When you click on the second button, the time will be 8 hours, on the third - 4 hours, on the fourth - 2 hours.
5. The timer is being activated.

User Marat Askarov spoke in detail about setting the time on the Sherkhan Magikar 5 alarm communicator.

Temperature trigger setting

When this function is activated, the readings of the temperature controller installed in the cabin are used. In the cold season, the values ​​can be -15 or -25 degrees, in the warm season - up to +60 degrees.

The setup is done like this:

1. The option to start the engine by timer is disabled.
2. The fourth key is clicked 21 times.
3. Using the keys, you select the threshold for disabling the option. Key 2 to turn on the internal combustion engine at -15 degrees Celsius, button 5 at -25 degrees, and 4 at +60.
4. After selecting a value, the option is activated.

Setting autostart based on on-board network voltage

If you configure this function, the autostart threshold will be 11.5 volts of voltage in the mains:

1. Key number 4 is clicked 20 times.
2. Voltage triggering is activated with the second button.
3. To change the operating time, the fourth key is clicked 12 times.
4. The time is selected using buttons 1-4.

How to disable autorun?

Resetting autorun settings is performed in the same way as their purpose. To disable the option, select the corresponding function on the key fob and set its inactive status.

The Galileosky channel spoke about the implementation and disabling of the autorun option.

Sherkhan Logicar 4

You can set the time on the remote alarm control key fob yourself by following these steps.

1. Press and hold the second and third buttons of the remote control for 2 seconds until the Pro9 picture lights up.
2. Click the first key once. The key fob will go to the time setting menu. The numbers will flash on the display.
3. Use the first key to adjust the clock. Button 2 – for setting minutes.
4. Once installation is complete, hold down the second and third keys for two seconds. There will be an exit from regulation.

Possible malfunctions of the Scher-Khan Magicar 5 alarm

If the autostart stops working and the engine does not start, the reason depends on the nature of the failure:

1. The power unit does not start, but the car owner has completed the reservation procedure. With such a problem, the first reason why the options do not work may be oxidation of the contacts on the safety device. The element is installed in the power supply circuit of the main module. The reason may also be the incorrect operation of the standard blocker bypass device. It is possible that the contact elements in the control relay may become stuck.
2. The engine starts, but stops after a few seconds of operation. If you start the engine with the key, it will turn on. The problem may be a failure of the five-pin relay, which is located in the microprocessor module.
3. Incorrect setting of the autorun function. To solve the problem, you need to reset all settings of the anti-theft system to factory settings. The option values ​​are then readjusted.
4. The problem may lie in the activated Valet service mode. If this function is enabled, the diode element will light without interruption. After disabling the service mode, the function will resume.

How to set 24 hours?

It will not be possible to set the 24-hour time format on the Magikar 5 key fob, since it is not provided. The 12-hour format includes AM and PM modes. 12 AM is midnight, 1:00 AM is already one in the morning. Noon is 12 RM, one o'clock is 1:00 RM. Be careful when setting time functions.

Find out why Sherkhan autostart does not work.

How to install an alarm?

The systems must be installed and connected as follows:

1. The battery is turned off to remove voltage from the on-board network.
2. The microprocessor device is being installed. To do this, you will need to remove the interior lining and place the unit in a hidden place. During installation, the device is securely fixed to prevent the negative impact of vibrations on the module. It is recommended to place the unit under the dashboard or in the free space behind it.
3. The siren is being installed under the hood of the car. The location must be chosen so that there are no sources of moisture or high temperatures nearby. The siren is mounted with the horn down to prevent moisture from accumulating inside. After installation, you need to make sure that the device and its wires will not be accessible from under the car.
4. An antenna module with a diode indicator is installed. These elements are installed on the inner surface of the windshield; it must first be cleaned and degreased. Fixation is carried out using glue or double-sided tape.
5. A temperature controller and a shock sensor are being installed. These elements are installed inside the car. Wires for connecting them are laid under a plastic lining.
6. Limit switches are installed on the doors, as well as the luggage compartment and hood. The wires from them must be laid so that they do not come into contact with moving parts of the body. Cables are laid under the cladding.
7. A service key is installed in the car interior. Its installation must be done in a hidden place, but the consumer must have access to the button from the driver's seat. The button can be disguised by wrapping it with black electrical tape.
8. At the final stage, all components are connected to the microprocessor module. An engine lock relay is connected to the ignition switch.